Single Phase Copy Stamford A. C. Sychronous Brushless Alternator 58 KW Hot Sale Generator





Features:

1.Any permanent magnetic generators, providing invariable excitation on all occasions.

2.Easy to be connected with power network or other generators. Standard 2/3 pitch windings check excessive midline current.

3.Balanced rotor with single ball bearing or  two sealed ball bearings

4.Convenient installation and maintenance with easy access to terminals, rotating diodes and coupling bolts

5.Wide range of Flange adaptor and single bearing coupling disc

6. Meet leading Industry and Marine standards

Electrical Charcter:

Excitation Systerm

AS440,SX460,SA465,SX440,SX421,MX341 or MX321

The main stator provides power for excitation of the exciter field via AVR

Output power of exciter's rotor is input to that of mains through 3-phase full wave rectifier.Two ends of the rectifier are connected with piezoresistance for restraining surge voltage and avoiding the impact caused by short circuit or parallel synchronization loss. Exciter's Stator is equipped with permanent magnetic steel, it can make generator starting smoothly in any occasions.

Voltage regulation(1.0%) and low frequency protection, exterior voltage adjustment of SX440,MX341 and Mx321 suitable for the generator with permanent magnetic generator (PMG)

Frame:

All industrial standard generators is IP21(NEMA1), also IP23 is optional, But rated power will decrease 5%,

Marine standard generators is Ip23. Air filter is optional, but rated power will decrease 5% if installed.

Axis and Key

All of the generator rotors pass balance test, The vibrations are lower than the minium of BS6861 P.A,  G2.5 two bearing generator has a half-key testing balance.

Terminal and Terminal  Box

The three-field generator has 12 leads brought out to the terminals in terminal box. The terminals are put on the non drive end. The box is equipped with removable panels

Engine Adaptor and Coupling Disc

SY-A Series single-bearing, engine adaptor: SAE0,1,2,3 and 4; Coupling discs: SAE8,10,11,.5,14 and 18 are available. 

SY-A Series double-bearing, engine adaptor: SAE0,1,2,3,4 and 5 are available. 

Voltage Regulation:

Voltage regulation refers to the change of voltage from non-load to with power factor ranging from 0.8 to 1 and 3%'s fluctuation of the speed of engine. Voltage is adjusted via potentiometer of AVR

Applications:It is suitable to match with any brands of the diesel engines in the world, such as USA brand, UK brand, Lovol,  Deutz,Volvo Penta,Kubota, Doosan and China made diesel engines. It can be used in land, watercraft, railway, hotel and the places need industry power. Our high-quality reliable AC generators are winning great acclaim from the domestic and abroad power generation market.








 

FAQ :

1. What's the delivery time,lead time?

Delivery within 25 days after deposit confirmed.
2. What's your payment terms?
1).We accept 30% T/T as the deposit,the balance payment  paid before delivery when see the copy of B/L.
2). L/C at sight.
4. What's your warranty & guaranty ?
Warranty is one year or 3000 hours which comes first. 
5. What's your MOQ?
MOQ  is 10 sets.
6. What's the frequency of diesel generators?
50Hz  & 60HZ .
7. What's the voltage of your diesel generator?
Voltage is 220/380V,230/400V,240/415V,110/220V,230/440V, just as per your request.
8.Q:Are you a factory or trading company?         A:  We are a famous  manufacturer named MINDONG MINSUN POWER,our engineers are from old MINDONG MOTOR factory .
  9. Q:Where is your factory located?           
     A: Our factory is in famous power city-FU'AN CITY,FUJIAN,near Taiwan.It is only 2 hours from Fuzhou airport by car;and 2.5 hours by     train from Xiamen Airport;6 hours from Shanghai Airport by train.
10 .Q:What is the material of your products?   
      A: We use AAA Grade Iron or Steel cast and 100% copper wire inside alternator.
 11.Q:How about quality control in your factory?      
A: MINDONG MINSUN POWER is a good reputiaon factory. We are always paying great attentions to quality controlling from the beginning to the end.We also have strict testing system and equipments for the all procedure of the production,and three engineers.
12. Can you supply spare parts?
A: Yes, we supply spare parts, if within the warranty, we can offer spare parts free.
13.Q: Is it all right to make customer's own brand name?
A: Yes,we can be your OEM manufacture with your authorization of     brand.
14.Q: What is your company's available production capacity?
A: 5000-10000 pieces  per month against your orders.
15.What is your main products and engine brands ,and power range?
A: Our main products are ---
1).Copy Stamford ,brushless alternator from the power 7.5 KVA to 2200 KVA .
2).ST,STC ,TZH carbon brush alternator from 2 KVA to 400 KVA.
3).We also have some famous brands of alternators for your options,such as original STAMFORD,LEROY SOMER,MECC,ENGGA,MARATHON etc. to match famous engines for gensets.

Single Phase Copy Stamford A. C. Sychronous Brushless Alternator 58 KW Hot Sale Generator





Features:

1.Any permanent magnetic generators, providing invariable excitation on all occasions.

2.Easy to be connected with power network or other generators. Standard 2/3 pitch windings check excessive midline current.

3.Balanced rotor with single ball bearing or  two sealed ball bearings

4.Convenient installation and maintenance with easy access to terminals, rotating diodes and coupling bolts

5.Wide range of Flange adaptor and single bearing coupling disc

6. Meet leading Industry and Marine standards

Electrical Charcter:

Excitation Systerm

AS440,SX460,SA465,SX440,SX421,MX341 or MX321

The main stator provides power for excitation of the exciter field via AVR

Output power of exciter's rotor is input to that of mains through 3-phase full wave rectifier.Two ends of the rectifier are connected with piezoresistance for restraining surge voltage and avoiding the impact caused by short circuit or parallel synchronization loss. Exciter's Stator is equipped with permanent magnetic steel, it can make generator starting smoothly in any occasions.

Voltage regulation(1.0%) and low frequency protection, exterior voltage adjustment of SX440,MX341 and Mx321 suitable for the generator with permanent magnetic generator (PMG)

Frame:

All industrial standard generators is IP21(NEMA1), also IP23 is optional, But rated power will decrease 5%,

Marine standard generators is Ip23. Air filter is optional, but rated power will decrease 5% if installed.

Axis and Key

All of the generator rotors pass balance test, The vibrations are lower than the minium of BS6861 P.A,  G2.5 two bearing generator has a half-key testing balance.

Terminal and Terminal  Box

The three-field generator has 12 leads brought out to the terminals in terminal box. The terminals are put on the non drive end. The box is equipped with removable panels

Engine Adaptor and Coupling Disc

SY-A Series single-bearing, engine adaptor: SAE0,1,2,3 and 4; Coupling discs: SAE8,10,11,.5,14 and 18 are available. 

SY-A Series double-bearing, engine adaptor: SAE0,1,2,3,4 and 5 are available. 

Voltage Regulation:

Voltage regulation refers to the change of voltage from non-load to with power factor ranging from 0.8 to 1 and 3%'s fluctuation of the speed of engine. Voltage is adjusted via potentiometer of AVR

Applications:It is suitable to match with any brands of the diesel engines in the world, such as USA brand, UK brand, Lovol,  Deutz,Volvo Penta,Kubota, Doosan and China made diesel engines. It can be used in land, watercraft, railway, hotel and the places need industry power. Our high-quality reliable AC generators are winning great acclaim from the domestic and abroad power generation market.








 

FAQ :

1. What's the delivery time,lead time?

Delivery within 25 days after deposit confirmed.
2. What's your payment terms?
1).We accept 30% T/T as the deposit,the balance payment  paid before delivery when see the copy of B/L.
2). L/C at sight.
4. What's your warranty & guaranty ?
Warranty is one year or 3000 hours which comes first. 
5. What's your MOQ?
MOQ  is 10 sets.
6. What's the frequency of diesel generators?
50Hz  & 60HZ .
7. What's the voltage of your diesel generator?
Voltage is 220/380V,230/400V,240/415V,110/220V,230/440V, just as per your request.
8.Q:Are you a factory or trading company?         A:  We are a famous  manufacturer named MINDONG MINSUN POWER,our engineers are from old MINDONG MOTOR factory .
  9. Q:Where is your factory located?           
     A: Our factory is in famous power city-FU'AN CITY,FUJIAN,near Taiwan.It is only 2 hours from Fuzhou airport by car;and 2.5 hours by     train from Xiamen Airport;6 hours from Shanghai Airport by train.
10 .Q:What is the material of your products?   
      A: We use AAA Grade Iron or Steel cast and 100% copper wire inside alternator.
 11.Q:How about quality control in your factory?      
A: MINDONG MINSUN POWER is a good reputiaon factory. We are always paying great attentions to quality controlling from the beginning to the end.We also have strict testing system and equipments for the all procedure of the production,and three engineers.
12. Can you supply spare parts?
A: Yes, we supply spare parts, if within the warranty, we can offer spare parts free.
13.Q: Is it all right to make customer's own brand name?
A: Yes,we can be your OEM manufacture with your authorization of     brand.
14.Q: What is your company's available production capacity?
A: 5000-10000 pieces  per month against your orders.
15.What is your main products and engine brands ,and power range?
A: Our main products are ---
1).Copy Stamford ,brushless alternator from the power 7.5 KVA to 2200 KVA .
2).ST,STC ,TZH carbon brush alternator from 2 KVA to 400 KVA.
3).We also have some famous brands of alternators for your options,such as original STAMFORD,LEROY SOMER,MECC,ENGGA,MARATHON etc. to match famous engines for gensets.

Cnc Milling features:

1, parts processing adaptability, flexibility, can process the shape of the contour is particularly complex or difficult to control the size of parts, such as mold parts, shell parts, etc.;
2. Able to process parts that cannot be processed by ordinary machine tools or are difficult to process, such as complex curve parts described by mathematical models and three-dimensional curved surface parts;
3. Parts that need to be processed in multiple processes after processing once clamping and positioning;
4, high machining accuracy, machining quality is stable and reliable, the pulse equivalent of CNC device is generally 0.001mm, high precision CNC system up to 0.1 m, in addition, Cnc Machining also avoid operator error;
5. High degree of production automation can reduce the labor intensity of operators.
It is beneficial to the automation of production management.
6, high production efficiency, CNC milling machine generally do not need to use special fixture and other special process equipment, in the replacement of the workpiece only need to call stored in the CNC device processing procedures, clamping tools and tool data can be adjusted, thus greatly shorten the production cycle.
Secondly, CNC milling machine with milling machine, boring machine, drilling machine function, so that the process is highly concentrated, greatly improve the production efficiency.
In addition, CNC milling machine spindle speed and feed speed are infinitely variable, so is conducive to the selection of the best cutting parameters

Cnc Turn-Mill

Cnc Turn-Mill,Cnc Turn-Mill Service,Turn-Milling Machining Parts,Cnc Machining Aluminum Turn-Mill

Chongqing Jin Te Rui Machine Co.,Ltd , https://www.die-casting-machine.com